Two Input 4K-60 HDMI Switcher With Integrated DTP2 Transmitter And HDMI Output

Product Description

Key FeaturesTransmits HDMI plus control and analog audio up to 330feet (100meters) over a shielded CATx cableDTP2 and HDMI outputsSupports computer and video resolutions up to 4K/60 @ 4: 4: 4Auto-switching between inputsAnalog stereo audio embeddingSupported HDMI2.0b specification features include data rates up to 18Gbps, HDR, Deep Color up to 12bit, 3D, and HD lossless audio formats specification Frame rate1 DTP2 output 24, 25, 30, 50, 60, or 120 fps HDMI output 24, 25, 30, 50, 60, 120, 144, or 240 fps Chroma sampling1 4: 4: 4, 4: 2: 2, or 4: 2: 0 Color bit depth1 8, 10, or 12 bits per color Signal Type HDMI 2.0b; HDCP 2.3 Max. video data rate 18 Gbps (6 Gbps per color) NOTE 1Subject to the maximum data rate limit. Use our calculator atwww.extron.com/8Kdatarateto determine video parameters supported by this data rate. Video NOTE Extron strongly recommends compatibility testing while designing, and before installing, any 3D system. There are several unique 3D formats in use by source devices and display manufacturers. The level of 3D product support is governed by pixel clock, signal format, and communication between source and sink devices. Please contact an Extron Applications Engineer for more information. Maximum data rate 18 Gbps (6 Gbps per color) Maximum pixel clock 600 MHz Resolution range Up to 2560x1600*@ 60 Hzor UHD (3840x2160 @ 60 Hz) with4: 4: 4 chromasubsampling *reduced blanking Color bit depth 8, 10, 12 bits subject to the maximum data rate limit Formats RGB and YCbCr digital video Standards DVI 1.0; HDMI 1.4, 2.0b; HDCP 1.4, 2.3; CEA-861-F Video input Number/signal type 2 single link HDMI (or DVI-D*) Connectors 2 female HDMI type A NOTE *Appropriate HDMI to DVI-D cables or adapters are required for DVI signal input/output. Video output Connectors 1 local HDMI output, 1 female RJ-45 output Horizontal frequency 24 kHz to 135 kHz for resolutions up to 18 Gbps Vertical frequency DTP2: 24 Hz to 120 Hz for resolutions up to 18 Gbps HDMI: 24 Hz to 240 Hz for resolutions up to 18 Gbps Termination standard TIA/EIA T568B Transmission distance Up to 330 (100 m) using shielded twisted pair (STP) cable or XTP DTP 24 STP cable Cable requirements Solid conductor, 24 AWG or better Cable recommendations 400 MHz bandwidth, STP (shielded twisted pair) NOTE Extron XTP DTP 24 shielded twisted pair cable is strongly recommended for optimal performance. Audio Gain Unbalanced output: 0 dB; balanced output +6 dB Frequency response 20 Hz to 20 kHz, 0.5 dB THD + Noise 0.03% @ 20 Hz to 20 kHz at maximum output S/N >90 dB, at maximum output (15 dBu), balanced (unweighted) Stereo channel separation >80 dB @ 1 kHz to 20 kHz Audio input Number/signal type 1 PC level stereo, unbalanced 2 Digital Embedded Audio on HDMI NOTE Analog audio can be configured for embedding onto the digital video signal at the Transmitter. Embedded digital audio can be (configured) de-embedded from the digital video signal at the Receiver end. Connectors (1) 3.5 mm stereo jack, 2 channel; tip (L), ring (R), sleeve (ground) (2) Female HDMI Impedance >10k ohms, DC coupled Nominal level -10 dBV (316 mVrms) Maximum level +7 dBV (unbalanced) NOTE 0 dBu = 0.775 Vrms, 0 dBV = 1 Vrms, 0 dBV 2 dBu Communications switcher Serial control port 1 RS-232, 3.5 mm,3-polecaptive screw connector, rear panel Pin configuration Pin 1 = Tx, Pin 2 = Rx, Pin 3 = GND Baud rate and protocol 9600 baud, 8 data bits, 1 stop bit, no parity Pin configuration Pins1 and2 of captive screw connector shorted together enable auto-input switching. USB control port 1 female mini USB, type B, front panel USB standards USB 2.0, high speed Contact closure/tally output (1) 3.5 captive screw connector, 3-pole (1) 3.5 captive screw connector, 4-pole Pin configuration Contact Closure - Pin 1 =Input 1 contact, Pin 1 = Input 2 contact, Pin 2 = GND (for both captive screw) Pin configuration Tally -Pin 3 = Input 1 tally ground, Pin 3 = Input 2 tally ground, Pin 4 = +5V (on Input 2 captive screw) Program control Extron Simple Instruction Set (SIS) Communications external device (RS-232/IR over TP) Quantity/type (1) RS-232 and IR via (1) 3.5 mm 5-pole captive screw connector Serial control pass-through ports (1) Bidirectional RS-232 Output/DTP Rx (1) RS-232 (1) 3.5 mm 5-pole captive screw connector (shared with IR port) Baud rate and protocol 300 to 115200 baud 8 or 7 data bits 1 or 2 stop bits No parity (default), even or odd parity Serial control pin configurations Pin 1 = Tx, Pin 2 = Rx, Pin 3 = GND IR control pass-through ports (1) bidirectional TTL level (0 to 5V) modulated infrared control from 30 KHz to 60 kHz Output/DTP Rx (1) RS-232 (1) 3.5 mm 5-pole captive screw connector (shared with RS-232 port) IR control pin configuration Pin 3 = GND, Pin 4 = IR Tx, Pin 5 = IR Rx General Power supply External Input: 100-240 VAC, 50-60 Hz Output: 12 VDC,2.0 A,24 Watts Power consumption Device 10.1 watts Device and power supply 12.5 watts Remote power budget 18 watts NOTE DTP2 devices can only send power to other DTP2 devices. DO NOT send power to DTP devices or they will be damaged. Ambient temperature/humidity Storage: -40 to +158 F (-40 to +70 C) / 10% to 90%, noncondensing Operating: +32 to +122 F (0 to +50 C) / 10% to 90%, noncondensing Cooling Convection, vents on top and sides Thermal dissipation Device 28.0 BTU/hr Device and power supply 36.5 BTU/hr Mounting Rack mount Yes, with optional rack shelf Back of the rack mountable with optional back-of-the-rack mounting kit Furniture mount Yes, with optional under-desk mounting kit Enclosure type Metal Enclosure dimensions 1.00" H x 8.75" W x 6.0" D (1 inchhigh, half rack wide) (2.54 cm H x 22.2 cm W x15.2 cm D) (Depth excludes connectors.) Product weight 1.0 lb (0.453 kg) Regulatory compliance CE, c-UL, UL, C-Tick, FCC Class A, ICES, RoHs, WEEE, VCCI Product warranty 3 years parts and labor Everlast power supply warranty 7 years parts and labor