Three Input Switcher With Integrated DTP Transmitter And Audio Embedding

Product Description

Key FeaturesTransmits HDMI or analog video, control, and analog audio up to 230feet (70meters) over a shielded CATx cableAutoswitching between inputsSupports computer and video resolutions up to 1920x1200, including 1080p/60 and 2KAnalog stereo audio embeddingRemote power capabilityExtronXTPDTP24 shielded twisted pair cable is strongly recommended for optimal performance Video VGA Gain Unity Bandwidth 170 MHz (-3 dB) Crosstalk -50 dB @ 10 MHz, -30 dB @ 100 MHz Switching speed <5 ms. (max) HDMI Maximum data rate 6.75 Gbps (2.25 Gbps per color) Maximum pixel clock 165MHz Resolution range Up to 1920x1200 or 1080p @ 60 Hz; 2k Formats RGB and YCbCr digital video Standards DVI 1.0, HDMI, HDCP 1.1, CEA-861E Video input HDMI Number/signal type 2 HDMI inputs (or single link DVI-D with the appropriate DVI-HDMI adapters) Connectors 2 female HDMI type A Video input VGA Number/signal type 1 VGA-QXGA; RGBHV Connectors 1 female 15-pin HD Nominal level 0.7 Vp-p Min./max. level Analog, 0.3 V to 1.5 Vp-p with no offset Impedance 75 ohms Horizontal frequency 15 kHz to 145 kHz Vertical frequency 30 Hz to 170 Hz Return loss <-40 dB @ 5 MHz NOTE The VGA input is digitized and output as DTP. The VGA signal is notscaled. Sync VGA Input type RGBHV, bi-level and tri-level sync Input level 1.9 V to 5.0 Vp-p S/N >90 dB at maximum input (unweighted) Max. input voltage 5.0 Vp-p Interconnection between transmitter and receiver Number/signal type 1 DTP 230 output Connector 1 female RJ-45 Termination standard TIA/EIA T568B Transmission distance Up to 230 (70 m) using shielded twisted pair cable or XTP DTP 24 STP cable Cable requirements Solid conductor, 24 AWG or better Cable recommendations 400 MHz bandwidth, STP (shielded twisted pair) NOTE Extron XTP DTP 24 shielded twisted pair cable is strongly recommended for optimal performance. NOTE Input and output mode signaling: DTP: HDMI with embedded audio, analog audio, RS-232 and IR, and remote power HDBT: HDMI with embedded audio plus RS-232 and IR Audio Gain Unbalanced output: 0 dB; balanced output +6 dB Frequency response 20 Hz to 20 kHz, 0.5 dB THD + Noise 0.01% @ 1 kHz at nominal level S/N >90 dB, at maximum input (unweighted) Crosstalk <-45 dB @ 20 kHz, or -72 dB @ 1 kHz or below Stereo channel separation >80 dB @ 1 kHz to 20 kHz Audio input Number/signal type 1 analog stereo, unbalanced or 2-digital audio, embedded in the HDMI Connectors 1 female 3.5 mm mini stereo jack 2 female HDMI Type A (shared with video input) Source formats HDMI LPCM up to 7.1/24-bit/192 kHz, Dolby TrueHD, Dolby Digital Plus, Dolby Digital EX, Dolby Digital 5.1, Dolby Digital 2/0 Surround, Dolby Digital 2/0, DTS-HD Master Audio, DTS-HD, DTS-ES Discrete 6.1, DTS-ES Matrix 6.1, DTS Digital Surround 5.1, DTS 2 Channel Analog Analog stereo audio Impedance 10k ohms, DC coupled Nominal level -10 dBV Maximum level +6dBV, unbalanced CMRR >60 dB typ @ 1 kHz Input gain adjustment -18 dB to +24 dB, 1 dB steps, adjustable per input NOTE 0 dBu = 0.775 Vrms, 0 dBV = 1 Vrms, 0 dBV 2 dBu Audio output Number/signal type 1 analog audio over DTP signal, or 1 embedded digital audio over DTP signal Connectors 1 RJ-45 jack Communications switcher Serial control port RS-232 via (1) 3.5 mm, 3 pole captive screw connector Serial control pin configuration Pin 1 = Tx, pin 2 = Rx, pin 3 = Gnd Baud rate and protocol (RS-232) 9600 baud, 8 data bits, 1 stop bit, no parity Tally port (1) 3.5 mm, 4 pole captive screw connector Tally port pin configuration Pin 1 = input 1 tally, pin 2 = input 2 tally, pin 3 = input 3 tally, pin 4 = +5 VDC Contact closure remote control (1) 3.5 mm, 4 pole captive screw connector Contact closure pin configuration Pin 1 = input 1, pin 2 = input 2, pin 3 = input 3, pin 4 = Gnd USB control port 1 front panel female mini USB, type B USB standards USB 2.0, high speed Program control Extron Simple Instruction Set (SISTM) Communications RS-232/IR over DTP NOTE Protocol is mirrored between the connected DTP 230 Rx and the Over DTP output port. Signals from a control device pass intothe Over DTP port, are embedded with the DTP signal, and sent to the DTP 230 Rx endpoint for control of remote sink and source devices. The Over DTP port is a pass-through connection to the DTP endpoint. There is no RS-232 or IR insertion from the DTP T USW 233 control port to the Over DTP port. Serial control pass-through port 1 RS-232 and IR via (1) 3.5 mm, 5-pole captive screw connector Serial control pin configuration Pin 1 = Tx, pin 2 = Rx, pin 3 = Gnd Baud rates 300 to 115200 baud Protocol 8 or 7 data bits 1 or 2 stop bits no parity (default) even or odd parity IR pass-through control port TTL level (0 to 5 V) modulated infrared control from 30 kHz up to 60 kHz IR control pin configuration 3 = Gnd, 4 = IR Tx, 5 = IR Rx General Power supply External Input: 100-240 VAC, 50-60 Hz Output: 12 VDC, 1.5 A, 18 watts Power consumption Device 4.7 watts Device and power supply 6.4 watts Remote power budget 12 watts NOTE The DTP T USW 233 can be powered either locally bythe external power supply or remotely by a receiver on the other end of thetwisted paircable. Ambient temperature/humidity Storage: -40 to +158 F (-40 to +70 C) / 10% to 90%, noncondensing Operating: +32 to +122 F (0 to +50 C) / 10% to 90%, noncondensing Cooling Convection, vents on top and sides Thermal dissipation Device 16.0 BTU/hour Device and power supply 21.6 BTU/hour Mounting Rack mount Yes, with optional 1U high rack shelf Furniture mount Yes, with optional under-desk mounting kit Enclosure type Metal Enclosure dimensions 1.0" H x 8.75" W x 6.0" D (half rack wide) (2.5 cm H x22.2 cm W x 15.2 cm D) (Depth excludes connectors.) Product weight 0.6 lbs (0.3 kg) Regulatory compliance CE, c-UL UL, CE, C-tick, FCC Class A, ICES, VCCI, Complies with the appropriate requirements of RoHS, WEEE