4K-60 HDMI DTP2 Transmitter With Audio Embedding

Product Description

Key FeaturesTransmits HDMI plus control and analog audio up to 330feet (100meters) over a shielded CATx cableSupports computer and video resolutions up to 4K/60 @ 4: 4: 4Analog stereo audio embeddingSupported HDMI2.0 specification features include data rates up to 18Gbps, 3D, HD lossless audio formats, and CEC pass-throughRemote power capability with DTP2 productsAccepts additional analog stereo audio signals specification Frame rate1 24, 25, 30, 50, or 60 fps Chroma sampling1 4: 4: 4 Color bit depth1 8 bits per color Signal Type HDMI 1.4, 2.0b;HDCP 1.4, 2.3 Max. video data rate 18 Gbps (6 Gbps per color) NOTE 1Subject to the maximum data rate limit. Use our calculator atwww.extron.com/8Kdatarateto determine video parameters supported by this data rate. Video NOTE Extron strongly recommends compatibility testing while designing, and before installing, any 3D system. There are several unique 3D formats in use by source devices and display manufacturers. The level of 3D product support is governed by pixel clock, signal format, and communication between source and sink devices. Please contact an Extron Applications Engineer for more information. Maximum data rate 18 Gbps (6 Gbps per color) Maximum pixel clock 600 MHz Resolution range 2560x1600 @ 60 Hz or 1080p @ 60 Hz, 4K (4096x2160) @ 30 Hz, UHD (3840x2160) @ 30 Hz, UHD (3840x2160) @ 60 Hz Color bit depth 8 bits subject to the maximum data rate limit Formats RGB digital video Standards DVI 1.0; HDMI 1.4, 2.0b; HDCP 1.4, 2.3, CEA-861-F Video input Number/signal type 1 single link HDMI (or DVI-D*) Connectors 1 female HDMI type A Horizontal frequency 15 kHz to 150 kHz Vertical frequency 24 Hz to 120 Hz for resolutions up to 18 Gbps NOTE *Appropriate HDMI to DVI-D cables or adapters are required for DVI signal input/output. Interconnection between transmitter and receiver Connectors 1 female RJ-45 per unit Termination standard TIA/EIA T568B Signal transmission distance Up to 330 (100 m) using shielded twisted pair (STP) cable or XTP DTP 24 STP cable Cable requirements Solid conductor, 24 AWG or better Cable recommendations 400 MHz bandwidth, STP (shielded twisted pair) NOTE Extron XTP DTP 24 shielded twisted pair cableis strongly recommended for optimal performance. Audio Gain Unbalanced output: 0 dBu; balanced output +6 dBu Frequency response 20 Hz to 20 kHz, 0.5 dB THD + Noise 0.03% @ 20 Hz to 20 kHz at maximum output S/N >90 dB, at maximum output (15 dBu), balanced (unweighted) Stereo channel separation >80 dB @ 1 kHz to 20 kHz Audio input Number/signal type 1 PC level stereo, unbalanced 1 Digital Embedded Audio on HDMI NOTE Analog audio can be configured for embedding onto the digital video signal at the Transmitter. Embedded digital audio can be (configured) de-embedded from the digital video signal at the Receiver end. Connectors (1) 3.5 mm stereo jack, 2 channel; tip (L), ring (R), sleeve (ground) (1) Female HDMI Impedance >10k ohms, DC coupled Nominal level -10 dBV (316 mVrms) Maximum level +7 dBV (unbalanced) NOTE 0 dBu = 0.775 Vrms, 0 dBV = 1 Vrms, 0 dBV 2 dBu Communication external device (pass-through, unidirectional or bidirectional) Serial control port input/output RS-232 via (1) 3.5 mm, 5 pole captive screw connector for RS-232 control (5 V) (connector is shared with IR control port) Serial control port output/input 1 set of proprietary signals on a female RJ-45 jack Baud rate and protocol 300 to 115200 baud, 8 or 7 data bits, 1 or 2 stop bits, non-parity (default), even or odd parity Serial control pin configuration 1 = Tx, 2 = Rx, 3 = Gnd IR control port (1) 3.5 mm, captive screw connector, 5 pole (connector is shared with RS-232 control port) TTL level (0 to 5 V) modulated infrared controlfrom 30 kHz up to 60 kHz IR control pin configuration 3 = Gnd, 4 = IR Tx, 5 = IR Rx General Power supply External (included with Tx) Input: 100-240 VAC, 50-60 Hz Output: 12 VDC,1.5 A,18 Watts Power consumption Device 4.9 watts Device and power supply 6.3 watts Remote power budget 18 watts NOTE Each transmitter or receiver can be powered either locally by an external power supply or remotely by receiver or transmitter on the other end of thetwisted paircable. NOTE DTP2 devices can only send power to other DTP2 devices. DO NOT send power to DTP devices or they will be damaged. Ambient temperature/humidity Storage: -40 to +158F (-40 to +70C) / 10% to 90%, noncondensing Operating: +32 to +122F (0 to +50C) / 10% to 90%, noncondensing Cooling Convection, vents Thermal dissipation Device 16.4 BTU/HR Device and power supply 21.2 BTU/HR Mounting Rack mount Yes, with optional 1U high rack shelf Furniture mount Yes, with optional under-desk mounting kit Enclosure type Metal Enclosure dimensions 1.0" H x 4.3" W x 6.0" D (quarter rack wide) (2.5 cm H x 10.9 cm W x15.2 cm D) (Depth excludes connectors.) Product weight 0.562 lb (0.255 kg) Regulatory compliance CE, C-Tick, FCC Class A, ICES, VCCI, KCC, c-UL, RoHS, UL UL rated for use in plenum airspaces: meets UL for heat and smoke release, excluding the power supply. Product warranty 3 years parts and labor Everlast power supply warranty 7 years parts and labor