XTP 4K Transmitter and Receiver Boards With RS-232 and IR Insertion

Product Description

Key FeaturesFour XTP inputs or four XTP outputs with RS-232 and IR insertionExtends video, audio, bidirectional RS-232 and IR, and Ethernet up to 330feet (100m) over a single, shielded CATx cableSupports computer and video resolutions up to 1920x1200, including 1080p/60 Deep Color and 2KHDCP compliantRemote power to select XTP transmitters and receiversExtron XTP DTP 24 shielded twisted pair cable is strongly recommended for optimal performance Video XTP CP 4i, XTP CP 4o Gain Unity Resolution range Up to 1920x1200*, 2K, or 1080p @ 60 Hz *reduced blanking Signal type Single-link HDMI (or DVI-D*) Digital video RGB digital video (DVI and HDMI standards) or Y, Cr, Cb digital component video (HDMI), actively buffered (supports all single-link DVI [if using an optional adapter] and HDMI standards from 640x480 @ 60 Hz to 1920x1200 @ 60 Hz) or 2K EDID and DDC Supports Extended Display Identification Data (EDID) and Display Data Channel (DDC) data using DVI and HDMI standards. EDID and DDC signals are actively buffered. HDCP Compliant with High-bandwidth Digital Content Protection (HDCP) using DVI and HDMI standards HPD Supports hot plug detection (HPD) of display as a pass-through signal. Maximum pixel clock 165 MHz Standards DVI 1.0, HDMI 1.3, HDCP 1.1 Switching speed 200 ns (max.) Video format HDMI and DVI Audio format Analog stereo, Dolby Digital, Dolby Digital EX, Dolby Digital Plus, Dolby TrueHD, DTS, DTS-ES, DTS 96/24, DTS-HD High Res, DTS-HD Master Audio, up to 8ch PCM, Dolby Atmos Shielded twisted pair interconnection Number/signal type 4 sets of proprietary signals Connectors 4 female RJ-45 per board Signal termination standards TIA/EIA T568B Input cable length Up to 330" (100 m) using shielded twisted pair or XTP DTP 24 cable NOTE Lower resolutions may support longer transmission distances. Transmission distance varies, depending on the signal resolution, type of cable, and source device used in the system. Cable requirements Solid conductor, 24 AWG or better Cable recommendations 400 MHz bandwidth, STP (shielded twisted pair) NOTE Extron XTP DTP 24 shielded twisted pair cable is strongly recommended for optimal performance. Control/remote external device (pass-through) Serial control pass-through ports 4 RS-232, via 3.5 mm, 5-pole captive screw connectors (shared with IR ports) Baud rates 300 to 115200 baud Protocol 5 to 8 data bits 1 or 2 stop bits no parity (default), even or odd parity flow control Xon, Xoff, and none Serial control pin configuration 1= Tx,2 = Rx,3 = GND Ethernet pass-through ports 4female RJ-45 Ethernet data rate 10/100Base-T, half/full duplex with autodetect IR control ports 4, via 3.5 mm, 5-pole captive screw connectors (shared withRS-232 ports) IR control pin configuration 3= GND,4 = IR Tx, 5 = IR Rx General Power Supplied by XTP CrossPoint or XTP II CrossPoint enclosure Power consumption XTP CP 4i PoE 79 watts (XTP II CrossPoint 3200) 95 watts (XTP II CrossPoint 6400) No PoE 35 watts XTP CP 4o PoE 75 watts (XTP II CrossPoint 3200) 90 watts (XTP II CrossPoint 6400) No PoE 21 watts Product weight 2.0 lbs (0.9 kg) Regulatory compliance Environmental Complies with the appropriate requirements ofRoHS, WEEE. Product warranty 3 years parts and labor