Control Processor

Product Description

Key Features Supports TouchLink Pro touchpanels, eBUS button panels, and Network Button Panels Supports secure industry standard communications protocols Supports LinkLicense One bidirectional RS-232 serial port with software handshaking One bidirectional RS-232/RS-422/RS-485 serial port with hardware and software handshaking One IR/Serial port for one-way control of external devices Memory SDRAM 512 MB Flash 4.5 GB Software Configuration software Global Configurator Plus and Professional Programming software Global Scripter Control apps Extron Control Resource management software GlobalViewer Enterprise Utilities Toolbelt, embedded web page Hardware user interface Hardware TouchLink Pro touchpanels, NBP button panels, or eBUS button panels Ethernet Network interface controllers (NICs) 1 Connector 1 female RJ-45 connector Data rate 10/100/1000Base-T, half/full duplex with autodetect Protocols DHCP, DNS, HTTP (redirect), HTTPS, ICMP, IEEE 802.1X , NTP, SFTP, SMTP, SNMP, SSH, TCP/IP, UDP/IP Default settings Link speed and duplex level = autodetected IP address = 192.168.254.250 Subnet mask = 255.255.255.0 Gateway = 0.0.0.0 DHCP = off DNS = 127.0.0.1 Serial Quantity/type 1 bidirectional RS-232, RS-422, RS-485 (port 1) 1 bidirectional RS-232 (port 2) Connector (1) 3.5 mm captive screw connector, 5 pole (1) 3.5 mm captive screw connectors, 3 pole Baud rate and protocol 300 to 115200 baud (9600 baud = default); 8 (default) or 7 data bits; 1 (default) or 2 stop bits; no parity (default), even, or odd parity NOTE The 5-pole ports support both hardware and software flow control. The 3-pole ports support software flow control. The default for both types of ports is no flow control. Pin configurations Serial, 5-pole captive screw RS-232 (default) Pin 1 = Tx, 2 = Rx, 3 = Gnd, 4 = RTS, 5 = CTS RS-422 Pin 1 = Tx-, 2 = Rx-, 3 = Gnd, 4 = Tx+, 5 = Rx+ RS-485 Pins 1 and 2 (tied together) = data-, 3 = Gnd, 4 and 5 (tied together) = data+ Serial, 3-pole captive screw Pin 1 = Tx, 2 = Rx, 3 = Gnd Digital I/O Quantity/type 4 digital input/output (configurable) Connectors (1) 3.5 mm captive screw connector, 5 pole Digital inputs Input voltage range 0 to 24 VDC, clamped at +30 VDC Input impedance >10k ohms Programmable pullup 1k ohms to +5 VDC Threshold low to high 2.8 VDC Threshold high to low 2.0 VDC Digital outputs 250 mA sink from 24 VDC max. Pin configurations 1, 2, 3, 4 = digital I/Os 1, 2, 3, 4; 5 = Gnd IR/serial Quantity/type 1 programmable: unidirectional RS-232 (5 V), or TTL level (0 to 5 V) infrared (carrier and non-carrier) up to 300 kHz Connector (1) 3.5 mm captive screw connector, 2-pole Baud rate and protocol (RS-232) 300 to 115200 baud (9600 baud = default); 8 (default) or 7 data bits; 1 (default) or 2 stop bits; no parity (default), even, or odd parity Pin configurations For each port, pin 1 = signal, 2 = Gnd IR output carrier frequency 30 kHz to 300 kHz IR learning carrier frequency 30 kHz to 300 kHz IR learning capture distance 2" (5.1 cm) to 12" (30.5 cm) from the front panel Relay Quantity/type 2 normally open relays Connector (1) 3.5 mm captive screw connector, 3 pole Relay control contact rating 24 VDC, 1 A Volume control Quantity/type 1 volume control (compatible with select Extron amplifiers) Connectors (1) 3.5 mm captive screw connector, 5 pole Pin configuration Pin 3 = 10 VDC reference voltage input, pin 4 = 0 to +10 VDC control voltage output, pin 5 = Gnd Control voltage output range 0 to +10 VDC (0.2 volts), adjustable eBUS eBUS control ports (1) 3.5 mm captive screw connector, 5 pole (uses 4 poles) eBUS pin configuration +V = +12 VDC; +S = + signal; -S = - signal; G = ground Recommended cable type Extron STP20-2/1000 or STP20-2P/1000 cable Maximum system cable length 1000 feet (305 meters) sum total for the eBUS system, regardless of topology. Power injection may be required depending on system cabling topology and primary power supply wattage. See the eBUS Technology Reference Guide for details. eBUS power output 6 watts General Power supply External, included Input: 100-240 VAC, 50-60 Hz Output: 12 VDC, 1.5 A, 18 watts Power input requirements 12 VDC, 1 A, 12 watts, max. Power consumption Device 8.8 watts, 12 VDC 3.4 watts without eBUS Device and power supply 11.0 watts, 100-240 VAC, 50-60 Hz 4.6 watts, 100-240 VAC, 50-60 Hz without eBUS Ambient temperature/humidity Storage: -40 to +158 F (-40 to +70 C) / 10% to 90%, noncondensing Operating: +32 to +122 F (0 to +50 C) / 10% to 90%, noncondensing Cooling Convection, no vents Thermal dissipation Device 9.5 BTU/ hr 11.5 BTU/hr without eBUS Device and power supply 16.8 BTU/hr 15.6 BTU/hr without eBUS Mounting Rack mount Yes, with optional 1U rack shelf Furniture mount Yes, with optional bracket kit Enclosure type Metal Enclosure dimensions 1.7" H x 4.3" W x 6.0" D (1U high, quarter rack wide) (43 mm H x 109 mm W x 152 mm D) (Depth excludes connectors.) Product weight 0.7 lbs (0.3 kg) Regulatory compliance CE, C-Tick, c-UL, FCC Class A, ICES, KC, UL, UL Listed for use in plenum air handling spaces, VCCI Complies with the appropriate requirements of RoHS, WEEE Product warranty 3 years parts and labor Everlast power supply warranty 7 years parts and labor