Matrix Blank Plate

Product Description

Key FeaturesCompatible with all XTP CrossPoint matrix switcher models Video input XTP CP 4i, XTP CP 4i DMA Number/signal type 4 sets of proprietary twisted pair AV signals Connectors 4 female RJ-45 per board NOTE Input comes froman ExtronXTP Series twisted pairtransmitter. Video output XTP CP 4o Number/signal type 4 sets of proprietary twisted pair AV signals Connectors 4 female RJ-45 per board NOTE Output connects to an ExtronXTP Series twisted pairreceiver. Video XTP CP 4i VGA Gain Unity Bandwidth 300 MHz (-3 dB), fully loaded 0-10 MHz: no more than +0.1 dB to -0.1 dB 0-130 MHz: no more than +0.8 dB to -0.8 dB Crosstalk -88 dB @ 1 MHz, -55 dB @ 10 MHz, -45 dB @ 30 MHz, -37 dB @ 100 MHz Switching speed 200 ms (max.) Video input XTP CP 4i VGA Number/signal type 4analog VGA-QXGA RGBHV, RGBS, RGsB, RsGsBs, HDTV, component video, S-video, composite video Connectors 4female 15-pin HD Nominal level 1 Vp-p for Y of component video and S-video, and for composite video 0.7 Vp-p for RGB and for R-Y and B-Y of component video 0.3 Vp-p for C of S-video Minimum/maximum levels Analog: 0.5 V to 2.0 Vp-p with no offset Impedance 75 ohms Return loss <-30 dB @ 5 MHz DC offset (max. allowable) 1.5 V Video processing XTP CP 4i VGA Decoder 8 bit digital Digital sampling 30 bit, 10 bits per color; 162 HMz standard Colors 1 billion Sync XTP CP 4i VGA Input type RGBHV, RGBS, RGsB, RsGsBs Input level 0.5 V to 5.0 Vp-p, 4.0 Vp-p normal Input impedance 510 ohms Horizontal frequency 15 kHz to 150 kHz Vertical frequency 30 Hz to 150 Hz Max. propagation delay 30 ns Max. rise/fall time 4 ns Polarity Positive or negative Video XTP CP 4i DVI Pro, XTP CP 4o DVI Pro NOTE *Appropriate DVI-D to HDMI cables or adapters are required for HDMI signal input/output. Gain Unity Resolution range Up to 1080p (HDTV) or 1920x1200 (the highest resolution of the single link DVI standard) @ 60 Hz Signal type Single link DVI digital video signals are supported. Digital video RGB digital video (DVI and HDMI standards) or Y, Cr, Cb digital component video (HDMI), actively buffered (supports all single link DVI and HDMI (if using an optional adapter) standards from 640x480 @ 60 Hz to 1920x1200 @ 60 Hz computer video) NOTE These XTP CP DVI Pro boardsarecompatible with HDMI 1.3. Digital audio Supports HDMI audio (if using an HDMI to DVI adapter) transmitted through the RGB and Y, Cr, Cb lines, actively buffered. Consumer Electronics Control (CEC) Not supported EDID and DDC Supports Extended Display Identification Data (EDID) and Display Data Channel (DDC) data using DVI and HDMI standards. EDID and DDC signals are actively buffered. HDCP Compliant with High-bandwidth Digital Content Protection (HDCP) using DVI and HDMI 1.3 standards HPD Supports hot plug detection (HPD) of display as a pass-through signal. Maximum data rate 6.75 Gbps (2.25 Gbps per color) Maximum pixel clock 165 MHz Standards DVI 1.0, HDMI 1.3, HDCP 1.1 Switching speed 200 ns, max. Video input XTP CP 4i DVI Pro Number/signal type 4 digital RGB single link DVI-D (or HDMI*) Connectors 4 female DVI-I (digital only) Equalization Automatic Input cable length >100 (30 m) at 1920x1200 @ 48, 50, or 60 Hz; or 1080p; 8 bit color NOTE The transmission distance varies depending on the signal resolution and on the type of cable, graphics card, and display used in the system. Video output XTP CP 4o DVI Pro Number/signal type 4 digital RGB single link DVI-D (or HDMI*) Connectors 4 DVI-I (digital only) Re-clocking Automatic Peripheral device power 5 VDC, 250 mA per output Video XTP CP 4i HDMI, XTP CP 4i HDMI DMA, XTP CP 4o HDMI NOTE *AppropriateHDMI to DVI-D cables or adapters are required forDVI signal input/output. Gain Unity Resolution range Up to 1080p (HDTV) or 1920x1200 (the highest resolution of the single link DVI standard) @ 60 Hz Signal type Single-link HDMI (or DVI-D*) Digital video RGB digital video (DVI and HDMI standards) or Y, Cr, Cb digital component video (HDMI), actively buffered (supports all single-link DVI (if using an optional adapter) and HDMI standards from 640x480 @ 60 Hz to 1920x1200 @ 60 Hz) Consumer Electronics Control (CEC) Not supported EDID and DDC Supports Extended Display Identification Data (EDID) and Display Data Channel (DDC) data using DVI and HDMI standards. EDID and DDC signals are actively buffered. HDCP Compliant with High-bandwidth Digital Content Protection (HDCP) using DVI and HDMI 1.3 standards HPD Supports hot plug detection (HPD) of display as a pass-through signal. Maximum data rate 6.75 Gbps (2.25 Gbps per color) Maximum pixel clock 165 MHz Standards DVI 1.0, HDMI 1.3, HDCP 1.1 Switching speed 200 ns, max. Video input XTP CP 4i HDMI, XTP CP 4i HDMI DMA Number/signal type 4 digital RGB single-link HDMI (or DVI-D*) Connectors 4 female HDMI type A Equalization Automatic Input cable length >100 (30 m) at 1920x1200 @ 48, 50, or 60 Hz; or 1080p; 8 bit color NOTE The transmission distance varies depending on the signal resolution and on the type of cable, graphics card, and display used in the system. Video output XTP CP 4o HDMI Number/signal type 4 digital RGB single-link HDMI (or DVI-D*) Connectors 4 female HDMI type A Re-clocking Automatic Peripheral device power 5 VDC, 250 mA per output Audio input XTP CP 4i DMA, XTP CP 4i HDMI DMA Source formats PCM, Dolby Digital 2/0, DolbyDigital2/0Surround, DolbyDigital5.1, DolbyDigitalEX, DTS Digital Surround 5.1, DTS-ESMatrix6.1, DTS-ESDiscrete6.1 Audio XTP CP 4i VGA, XTP CP 4o SA Gain Unbalanced output: -6 dB; balanced output 0 dB Frequency response 20 Hz to 20 kHz, 0.05 dB THD + Noise 0.03% @ 1 kHz at nominal level S/N >90 dB at maximum output (21 dBu, unweighted) (balanced) Crosstalk <-80 dB @ 1 kHz, fully loaded Stereo channel separation >80 dB @ 1 kHz CMRR >75 dB @ 20 Hz to 20 kHz Audio input XTP CP 4i VGA Number/signal type 4 stereo, balanced/unbalanced Connectors (4) 3.5 mm captive screw connector, 5 pole Impedance >10k ohms unbalanced/balanced, DC coupled Nominal level 0 dBu (0.775 Vrms) Maximum level +19.5 dBu, (balanced or unbalanced) at 1% THD+N Input gain adjustment -18 dB to +18 dB, adjustable per input; default = 0 dB NOTE 0 dBu = 0.775 Vrms, 0 dBV = 1 Vrms, 0 dBV 2 dBu Audio output XTP CP 4o SA Number/signal type 4 stereo, balanced/unbalanced Connectors (4) 3.5 mm captive screw connector, 5 pole Impedance 50 ohms unbalanced, 100 ohms balanced Gain error 0.1 dB channel to channel Maximum level (Hi-Z) >+21 dBu, balanced or unbalanced at 0.1% THD+N Maximum level (600 ohm) >+15 dBm, balanced or unbalanced at 0.1% THD+N Volume control range -98 dB to 0 dB (volume numbers 0 through 64) in a 35 dB increment from step 0 to step 1, then in 1 dB increments from steps 1 to 64; default = 64 (0dB) NOTE Attenuation = volume number minus 64. The default is 0 dB = volume number 64. Audio XTP CP 4i DVI Pro, XTP CP 4o DVI Pro, XTP CP 4i HDMI, XTP CP 4o HDMI Gain Unbalanced output: -6 dB; balanced output 0 dB Frequency response 20 Hz to 20 kHz, 0.05 dB THD + Noise 0.01% @ 1 kHz at nominal level S/N >105 dB at maximum output (21 dBu, unweighted) (balanced) Crosstalk <-89 dB @ 1 kHz, fully loaded Stereo channel separation >105 dB @ 1 kHz CMRR >83 dB @ 20 Hz to 20 kHz Audio input XTP CP 4i DVI Pro, XTP CP 4i HDMI Number/signal type 4 stereo, balanced/unbalanced Connectors (4) 3.5 mm captive screw connector, 5 pole Impedance >10k ohms unbalanced/balanced, DC coupled Nominal level +4 dBu (1.228 Vrms) Maximum level +21 dBu, (balanced or unbalanced) at 0.01% THD+N +19.5 dBu, (balanced or unbalanced) at 1% THD+N Input gain adjustment -18 dB to +18 dB, adjustable per input; default = 0 dB Audio output XTP CP 4o DVI Pro, XTP CP 4o HDMI Number/signal type 4 stereo, balanced/unbalanced Connectors (4) 3.5 mm captive screw connector, 5 pole Impedance 50 ohms unbalanced, 100 ohms balanced Gain error 0.1 dB channel to channel Maximum level (Hi-Z) >+21 dBu, balanced or unbalanced at 1% THD+N Maximum level (600 ohm) >+20 dBm, balanced or unbalanced at 1% THD+N Volume control range -75.8 dB to 0 dB (volume numbers 0 through 64) in a 35 dB increment from step 0 to step 1, then in 1 dB increments from steps 1 to 64; default = 64 (0dB) NOTE Attenuation = volume number minus 64. The default is 0 dB = volume number 64. Control/remote switcher host ports NOTE The front panel USB port and rear panel RS-232 port are independent of each other and can be used at the same time. Serial host control port 1 bidirectional RS-232 or RS-422, rear panel female 9-pin D connector Baud rate and protocol 9600 (default) to 115200 baud, 8 data bits, 1 stop bit, no parity, no flow control Serial control pin configurations RS-232 2 = Tx, 3 = Rx, 5 = GND RS-422 2 = Tx-, 3 = Rx-, 5 = GND, 7 = Rx+, 8 = Tx+ USB control port 1 front panel female mini USB B USB standards USB 2.0, low speed Ethernet control port 1 female RJ-45 Ethernet data rate (for network communication) 10/100Base-T, half/full duplex with autodetect Ethernet protocol ARP, ICMP (ping), IP, TCP, DHCP, HTTP, SMTP, Telnet Ethernet default settings Link speed and duplex level = autodetected IP address = 192.168.254.254 Subnet mask = 255.255.0.0 Default gateway = 0.0.0.0 DHCP = off Web server Up to 200 simultaneous sessions 7.0 MB nonvolatile user memory Program control Extron control/configuration program for Windows Extron Simple Instruction Set (SIS) MicrosoftInternet Explorerver. 6 or higher, Telnet Control/remote external device (pass-through, unidirectional or bidirectional) Ethernet pass-through port 1 female RJ-45 connector Ethernet data rate 10/100Base-T, half/full duplex with autodetect General Power Internal Input: 100-240 VAC, 50-60 Hz XTP CrossPoint 1600 Redundant power supply is optional. XTP CrossPoint 3200 Redundant power supply is standard. Power consumption XTP CrossPoint 1600 300 watts XTP CrossPoint 3200 500 watts Individual I/O boards TBD Temperature/humidity Storage: -40 to +158 F (-40 to +70 C) / 10% to 90%, noncondensing Operating: +32 to +122 F (0 to +50 C) / 10% to 90%, noncondensing Cooling Fan, left to right (as viewed from front panel) Mounting Rack mount Yes Enclosure type Metal Enclosure dimensions (Depth excludes connectors. Width excludes rack ears.) XTP CrossPoint 1600 8.75" H x 17.0" W x 15.0" D (5U high, full rack wide) (22.2 cm H x 43.2 cm W x 38.1 cm D) XTP CrossPoint 3200 17.5" H x 17.0" W x 17.5" D (10U high, full rack wide) (44.5 cm H x 43.2 cm W x 44.5 cm D) Product weight with boards installed XTP CrossPoint 1600 18.1 lbs (8.3 kg) XTP CrossPoint 3200 33.4 lbs (15.2 kg) Shipping weight with boards installed XTP CrossPoint 1600 23 lbs (11 kg) XTP CrossPoint 3200 42 lbs (20 kg) Shipping weight of individual boards, if purchased separately 2 lbs (1 kg) DIM weight XTP CrossPoint 1600 25 lbs (12 kg) XTP CrossPoint 3200 44 lbs (20 kg) Vibration ISTA 1A in carton (International Safe Transit Association) Regulatory compliance Safety CE, c-UL, UL EMI/EMC CE, C-tick, FCC Class A, ICES, VCCI MTBF 30,000 hours Product warranty 3 years parts and labor