HDMI 1G Pro AV Over IP Encoder

Product Description

Key Features New Expanded AES67 capabilities enable any NAV encoder or decoder to transmit or receive an AES67 audio stream New Confidence Preview available in the endpoint or NAVigator browser interface Encodes and streams video and audio over 1Gbps Ethernet networks Supports HDMI2.0 at resolutions up to 4K/60 @ 4: 4: 4 PURE3 Codec PURE3 Intelligent Selective Streaming specification Frame rate2 24, 25, 30, 50, or 60 fps Chroma sampling2 4: 4: 4, 4: 2: 2, or 4: 2: 0 Color bit depth2 8, or 10 bits per color Signal Type DVI v 1.0, HDMI v1.4 and v2.0, HDCP v1.4 and v2.3 Max. video data rate 18 Gbps (6 Gbps per color) NOTE 14096 x 2160 @ 50-60 Hz is available only for HDMI connectors. NOTE 2Subject to the maximum data rate limit. Use our calculator at www.extron.com/8Kdatarate to determine video parameters supported by this data rate. Video input and loop through NOTE *Appropriate DVI-D to HDMI or DisplayPort to HDMI cables or adapters are required for DVI or DisplayPort signal input. Number/signal type 1 digital HDMI video (input)* 1 digital HDMI video (loop through) Connectors 2 female HDMI type A: 1 for input, 1 for loop through Resolution range Up to 4K (4096x2160 at 60 Hz) and UHD (3840x2160 at 60 Hz) Standards DVI v1.0, HDMI v1.4 and v2.0, HDCP v1.4/v2.3 Video processing Digital sampling 8 or 10 bits per color; 600 MHz pixel clock maximum Compression PURE3 Bit rate 250 Mbps to 900 Mbps Latency <1 frame (encode/decode) NOTE Indicates minimum latency. Network and video processing dependencies apply. Video output stream Number/signal type 1 PURE3 digital video over IP Connector 1 RJ-45 connector Audio Gain Analog to analog: -6.5 dBu balanced, -12.5 dBu unbalanced HDMI to analog: -5.3 dBu blanced, -11.3 unbalanced Frequency response 20 Hz to 20 kHz, +0.5 dB THD + Noise <0.1% @ 20 Hz to 20 kHz at nominal level S/N Analog to digital: >90 dB, at full scale output, unweighted Digital to analog: >90 dB, at maximum balanced output, unweighted Analog to analog: >90 dB, at maximum balanced output, unweighted Crosstalk <-80 dB @ 1 kHz, fully loaded Stereo channel separation >80 dB @ 1 kHz Sampling Rates 32, 44.1, 48 kHz Bit depths 16, 20, 24 bit Audio input Number/signal type 1 analog stereo, unbalanced or balanced 1 digital stereo, de-embedded from HDMI Connectors (1) 3.5 mm captive screw connector, 5 pole 1 female HDMI type A (shared with video input) Supported formats LPCM (2 channel), analog stereo audio Impedance >10k ohms unbalanced, >20k ohms balanced Nominal level +4 dBu, -10 dBV configurable Maximum level +21 dBu balanced, +15 dBu unbalanced Gain adjustment range Adjustable, -18 dB to +10 dB NOTE 0 dBu = 0.775 Vrms, 0 dBV = 1 Vrms, 0 dBV 2 dBu Audio output stream Number/signal type 1 audio over IP LPCM 1 audio over IP AES67* Connector 1 RJ-45 connector NOTE *AES67 specifications are compatible with the Extron DSPs. Network interconnection (NAV) Connector type 1 RJ-45 female Ethernet standards 1GbE (802.3ab), 10/100/1000 Base-T, half/full duplex with autodetect Termination Auto-MDIX, TIA/EIA T568B Power over Ethernet (PoE) Complies with IEEE 802.3at Type 2 (PoE+), class 4 Protocols Streaming SRTP (AES-128) on video, audio, and USB Transport Multicast UDP All supported DHCP, HTTPS, IGMPv2/v3, IPv4, PTPv2, QoS, SSH, TCP, UDP Security AES-256, 802.1X, Active Directory authentication Signal transmission distance 330 (100 m) using CAT 5e/6/6a/7 cables Communications - external devices Serial Quantity/type 1 bidirectional RS-232 Connector (1) 3.5 mm captive screw connector, 5 pole (shared with IR port) Baud rate and protocol 300 to 115200 baud (9600 baud = default) 8 (default) or 7 data bits 1 (default) or 2 stop bits no parity (default), even or odd parity Pin configuration Tx, Rx, and Gnd IR control Quantity/type 1 TTL level (0 to 5 V) infrared (carrier and non-carrier) up to 300 kHz Connector (1) 3.5 mm captive screw connector, 5-pole (shared with RS-232) Pin configuration S = signal and G = Gnd IR output carrier frequency 30 kHz to 300 kHz Contact closure Quantity/type 1 contact closure input Connector (1) 3.5 mm captive screw connector, 2 pole (shared with tally) Input voltage range 0 to 5 VDC, clamped at +5.1 VDC Pin configuration C = contact input (+5 VDC) (Ground is supplied by HDMI connector on an Extron Show-Me cable) Tally port Quantity/type 1 tally output Connector (1) 3.5 mm captive screw connector, 2 pole (shared with contact closure) Pin configuration T = tally output (GND) (+5 VDC is supplied by HDMI connector on an Extron Show-Me cable) USB configuration port Quantity/type 1 front panel USB mini-B Standard Ethernet over USB General Power supply External Input: 100-240 VAC, 50-60 Hz Output: 12 VDC, 2.0 A, 24 watts NOTE Each 1G endpoint can be powered either locally by an external power supply or remotely using optional PoE+. Power consumption Device 18.9 watts Device and power supply 21.2 watts PoE Complies with IEEE 802.3at Type 2 (PoE+), class 4 Ambient temperature/humidity Storage: -40 to +158 F (-40 to +70 C) / 10% to 90%, noncondensing Operating: +32 to +104 F (0 to +40 C) / 10% to 85%, noncondensing Cooling Fan, air flows from top to rear Thermal dissipation Device 63.7 BTU/hr Device and power supply 71.6 BTU/hr Device with PoE 67.9 BTU/hr Mounting Rack mount Yes, with optional rack shelf Furniture mount Yes, with optional under desk mounting kit Enclosure type Metal Enclosure 1.00" H x 8.75" W x 6.00" D* (half rack wide) (25 mm H x 222 mm W x 152 mm D*) (Depth excludes connectors) Product weight 1.5 lbs (0.68 kg) Regulatory compliance CE, c-UL UL,C-tick, FCC Class A, ICES, KC, VCCI, Complies with the appropriate requirements of RoHS, WEEE Product warranty 3 years parts and labor Everlast power supply warranty 7 years parts and labor