Fiber Optic Scaling Receiver For HDMI USB HID Audio Control And 3D Sync

Product Description

Key FeaturesSupports KVM System Configuration and Control in a FOX3 Matrix systemOn-Screen Display provides source information on the workstation displayReceives fiber optic signals from FOX3 Series transmitters and provides scaled HDMI video, USB HID, stereo audio, RS-232 control, IR control, and 3D sync signalsHigh-performance scaler provides selectable output resolutions up to 4096x2160 at 60 Hz with 4: 4: 4 chroma samplingSupports mathematically lossless 4K video up to 4096x2160 at 60 Hz with 4: 4: 4 chroma sampling over one fiberSupports uncompressed 4K video up to 4096x2160 at 60 Hz with 4: 4: 4 chroma sampling over two fibers specification Frame rate3 24, 25, 30, 50, or 60 fps Chroma sampling3 4: 4: 4, 4: 2: 2 Color bit depth2,3 8, 10, or 12 bits per color Signal Type HDMI 2.0, HDCP 2.3 Max. video data rate 18.0 Gbps NOTE 1Supports lossless 4K video over one fiber or uncompressed 4K video over two fibers. 2Supports 12-bit color bit depth for uncompressed 4K video over two fibers. When using a FOX3 SR scaling receiver, the scaler must be in bypass mode to pass 4K video with a 12-bit color bit depth. 3Subject to the maximum data rate limit. Use our calculator atwww.extron.com/8Kdatarateto determine video parameters supported by this data rate. NOTE This product contains Class 1 laser. It meets the safety regulation of IEC 60825-1, FDA 21 CFR 1040.10, and FDA 21 CFR 1040.11. Optical fiber interconnection between transmitter and receiver Number/type 1 or 2 SFPs Connectors 1, 2, or 3 LC connectors Operating distance Singlemode 20 km (12.4 miles) with singlemode (SM) cables Multimode 500 m (1640 feet) with 50 m OM4 4700 MHz bandwidth laser optimized multimode cables NOTE The system works with OM1, OM2, and OM3 fiber at reduced distances. NOTE Operating distance is approximate.These are typical maximum distances that may vary depending on factors such as fiber type, fiber bandwidth, connector splicing, losses, modal or chromatic dispersion, environmental factors, and kinks. Nominal peak wavelength 850 nm for multimode, 1310 nm for singlemode Data rate 10.0 Gbps (1 fiber) or 20.0 Gbps (2 fibers) Transmission power Singlemode -5.2 dBm, minimum Multimode -2.8 dBm, minimum Maximum receiver sensitivity Singlemode -12.6 dBm, maximum Multimode -11.1 dBm, maximum Optical loss budget Singlemode +7.4 dB, maximum Multimode +8.3 dB, maximum Video Maximum data rate 18.0 Gbps (6.0 Gbps per color) Maximum pixel clock 594 MHz Resolution range 640x4808up to 4096x21601,2,3,4,5,6,7,8, 480p7,8, 576p6, 720p3,4,5,6,7,8,9, 1080i6,7,8, 1080p1,2,3,4,5,6,7,8,9, 2K1,2,3,4,5,6,7,8,3840x21601,2,3,4,5,6,7,8, 4096x21601,2,3,4,5,6,7,8 123.98Hz,224Hz,325 Hz,429.97 Hz,530 Hz,650 Hz,759.94 Hz,860 Hz,9120 Hz Frame rate 24, 25, 30, 50, 60, or 120 fps Color space 4: 4: 4, 4: 2: 2 Color bit depth 8, 10, and, 12 bits per color Standards HDMI 2.0, HDCP 2.3 Horizontal frequency 24 kHz to 135 kHz for resolutions up to 18 Gbps Vertical frequency 24 Hz to 120 Hz for resolutions up to 18 Gbps Format RGB and YCbCr digital video Video output Number/signal type 1 HDMI Connectors 1 female HDMI type A Power for active cables 1.1 W max. for the HDMI port Audio Gain Unbalanced output: -6dB; balanced output: 0 dB (default) Frequency response 20 Hz to 20 kHz, 0.5 dB THD + Noise <0.1% @ 20 Hz to 20 kHz at nominal level S/N >90 dB at maximum output (unweighted) CMRR 65 dB @ 20 Hz to 20 kHz Stereo channel separation >80 dB @ 1 kHz Bit Depth 16, 20, 24 Sampling rate 48 kHz Audio output Number/signal type 1 digital audio, embedded with HDMI (2-CH PCM only) output or 1 analog stereo, balanced/unbalanced Connectors 1 femaleHDMI (shared with video output) (1) 3.5 mm captive screw connector, 5 pole Supported formats HDMI 2 CH LPCM Analog Analog stereo audio Impedance 50 ohms unbalanced, 100 ohms balanced (analog only) Maximum level (Hi-Z) +21 dBu balanced, +15 dBu unbalanced Gain error 0.5 dB channel to channel Volume control range 100% to 0% (0-100 in 1dB steps) NOTE 0 dBu = 0.775 Vrms, 0 dBV = 1 Vrms, 0 dBV 2 dBu Audio return input Number/signal type 1 analog stereo, balanced/unbalanced Connectors (1) 3.5 mm captive screw connector, 5 pole Impedance 10 k ohms unbalanced, 20 k ohms balanced Nominal level +4 dBu (1.23 Vrms), -10 dBV (316 mVrms) Maximum level +21 dBu balanced, +15 dBu unbalanced NOTE 0 dBu = 0.775 Vrms, 0 dBV = 1 Vrms, 0 dBV 2 dBu Communications USB configuration port Number/type 1 front panel mini USB B, female Standard Ethernet over USB Serial host control port Control 1 RS-232, 3.5 mm captive screw connector, 5-pole (3 pins are used), rear panel Pass-through 1 RS-232, 3.5 mm captive screw connector, 5-pole (3 pins are used), rear panel Baud rate and protocol Control 9600 baud, 8 data bits, 1 stop bit, no parity Pass-through 9600 to 115,200 baud Serial control pin configuration Captive screw: 1 = Tx, 2 = Rx, 3 = GND IR control port (1) 3.5 mm captive screw connector, 5 pole (connector is shared with RS-232 pass thru) TTL level (0 to 5V) modulated infrared control from 30 kHz to56 kHz IR control pin configuration 3 = GND, 4 = IR Tx, 5 = IR Rx Ethernet control Ethernet port 1 RJ-45 connector, female Ethernet data rate 10/100/1000Base-T, half/full duplex with autodetect Protocols ARP, ICMP (ping), DHCP, DNS, HTTPS, SFTP, SSH, TCP/IP, UDP/IP Default settings Link speed and duplex level = autodetected IP address = 192.168.254.254 Subnet mask = 255.255.255.0 Gateway = 0.0.0.0 DHCP = off Program control Extron Product Configuration Software Extron Simple Instruction Set (SIS) USB extension USB standards USB 2.0, USB 1.1 USB data rates Low speed (1.5 Mbps), full speed (12 Mbps), high speed (480Mbps) Data transfer types Bulk, control, interrupt, and isochronous USB device ports FOX3 R 301 Number/signal type (1) 2-port USB HID (No external hubs can be connected to these ports) (1) 1-port USB 2.0 Connectors 3 USB type A, female (2 USB HID and 1 USB 2.0) USB 2.0 Maximum built-in USB hubs 0 Minimum built-in USB hubs 0 USB HID Maximum built-in USB hubs 0 Minimum built-in USB hubs 0 Available USB power USB 2.0 port = 500 mA USB HID ports = 100 mA FOX3 R 311 Number/signal type (1) 2-port USB HID hub (No external hubs can be connected to these ports) Connectors 2 USB type A, female (2 USB HID) USB HID Maximum built-in USB hubs 0 Minimum built-in USB hubs 0 Available USB power USB HID ports = 100 mA NOTE When configured endpoint to endpoint, there are 0 hubs. When configured with a FOX3 Matrix, there is 1 hub. General Power supply Internal Input: 100-240 VAC, 50-60 Hz Power consumption 24.4watts Ambient temperature/humidity Storage: -40 to +158F (-40 to +70C) / 10% to 90%, noncondensing Operating: +32 to +122F (0 to +50C) / 10% to 90%, noncondensing Cooling Fan, air flows from front to rear (vented) Thermal dissipation 71.0 BTU/hr Mounting Rack mount Yes, with optional rack shelf Furniture mount Yes, with optional under desk mounting kit Enclosure type Metal Enclosure dimensions 1.7" H x 8.75" W x 8.5" D (half rack wide) (4.4cm H x22.2 cm W x21.6 cm D) (Depth excludes connectors.) Product weight 2.4 lbs (1.1 kg) Regulatory compliance CE, c-UL, C-tick, FCC Class A, ICES,UL, VCCI Complies with the appropriate requirements of RoHS, WEEE. Product warranty 3 years parts and labor Everlast power supply warranty 7 years parts and labor