Fiber Optic Input And Output Boards with RS-232 And IR Insertion
Product Details:
- Power Source AC/DC
- Features High Quality
- Input AC/DC
- Product Type electrical products
- Application Electrical & Electronics
- Size Standard
- Function Electrical & Electronics Equipment
- Click to View more
X
Fiber Optic Input And Output Boards with RS-232 And IR Insertion Product Specifications
- 50 Hertz(Hz)
- Standard
- Electrical & Electronics Equipment
- as shown in the image
- Electrical & Electronics
- High Quality
- AC/DC
- AC/DC
- electrical products
Product Description
Key FeaturesFour fiber optic inputs or outputs with RS-232 and IR insertionExtends video, audio, bidirectional RS232 and IR, and Ethernet over one fiber optic cableSupports computer and video resolutions up to 4KHDCP compliantBidirectional RS232 and IR insertion for AV device controlEthernet extension Video XTPCP 4iFiber 4K, XTPCP 4oFiber 4K NOTE Extron strongly recommends compatibility testing while designing, and before installing, any 3D system. There are several unique 3D formats in use by source devices and display manufacturers. The level of 3D product support is governed by pixel clock, signal format, and communication between source and sink devices. Please contact an Extron Applications Engineer for more information. Gain Unity Resolution range Up to 2560x1600 @ 60 Hz*, 1080p @ 120 Hz or 4K (4096x2160) @24 Hz, UHD (3840x2160) @ 30 Hz UHD @ 60 Hz with 4: 2: 0 color subsampling *reduced blanking Signal Type Single-link HDMI (or DVI-D or DisplayPort) Maximum data rate 8.91 Gbps (2.97 Gbps per color) Maximum pixel clock 300 MHz Video formats RGB and YCbCr digital video Standards Refer to XTP endpoints Switching speed 200 ms (max.) Audio format Analog stereo, DolbyDigitalDolby Digital EX, Dolby Digital Plus, Dolby TrueHD, Dolby Atmos , DTS, DTS-ES, DTS 96/24, DTS-HD High Res, DTS-HD Master Audio , up to 8ch PCM, Optical fiber interconnection Number/signal type 4 sets of proprietary signals Connectors 4 LC fiber connector Operating distance NOTE Operating distance is approximate. These are typical maximum distances that may vary depending on factors such as fiber type, fiber bandwidth, connector splicing, losses, modal or chromatic dispersion, environmental factors, and kinks. Singlemode 10 km (6.2 miles) with singlemode cables Multimode 200 m (650) with 62.5 m OM1 multimode cable 300 m (980) with 50 m OM2 multimode cable 400 m (1312) with 50 m OM3 2000 MHz bandwidth laser optimized cable multimode cable 500 m (1640) with 50 m OM4 4700 MHz bandwidth laser optimized cable multimode cable NOTE Multimode units are compatible with OM1 and OM2 multimode cables, but at reduced operating distances. Nominal peak wavelength Singlemode 1490 nm, 1550 nm, 1310 nm Multimode 850 nm, 980 nm, 780 nm Data rate 8.5 Gbps Transmission power Singlemode -6 dBm, typical Multimode -5 dBm, typical Maximum receiver sensitivity Singlemode -15 dBm, typical Multimode -13 dBm, typical Optical loss budget Singlemode 9 dB, maximum Multimode 8 dB, maximum Communications external device (pass-through, unidirectional or bidirectional) Serial control pass-through ports RS-232 (5 V)via (4) 3.5 mm, 5 pole captive screw connectors (uses 3 poles) (connector is shared with IR control ports) Baud rates 300 to 115200 baud Protocol 5 to 8data bits 1 or 2 stop bits no parity (default), even or odd parity flow control Xon, Xoff, and none Serial control pin configuration 1 = Tx, 2 = Rx, 3 = Gnd IR control port (4) 3.5 mm, captive screw connector, 5-pole (uses 3 poles) (connector is shared with RS-232 control ports) TTL level (0 to 5 V) modulated infrared control from 30 kHz up to 56 kHz IR control pin configuration 3 = Gnd, 4 = IR Tx, 5 = IR Rx Ethernet pass-through ports 4 female RJ-45 Ethernet data rate 10/100Base-T, full duplex with autodetect General Power Supplied by XTP CrossPoint or XTP II CrossPoint enclosures Power consumption 19 watts Product weight 2.0 lbs (0.9 kg) Regulatory compliance Complies with the appropriate requirements ofRoHS, WEEE. Product warranty 3 years parts and laborFAQs of Fiber Optic Input And Output Boards with RS-232 And IR Insertion:
Q: What are the input and power source options for the Fiber Optic Input And Output Boards with RS-232 And IR Insertion?
A: The boards support both AC and DC as input and power source options.Q: What is the size category of the Fiber Optic Input And Output Boards with RS-232 And IR Insertion?
A: The size of the boards falls under the standard category.Q: What type of applications can the Fiber Optic Input And Output Boards with RS-232 And IR Insertion be used for?
A: These boards are specifically designed for use in electrical and electronics applications.Q: What frequency does the Fiber Optic Input And Output Boards with RS-232 And IR Insertion operate on?
A: The boards operate at a frequency of 50 Hertz (Hz).Q: What features ensure the reliability of the Fiber Optic Input And Output Boards with RS-232 And IR Insertion?
A: The boards are built with high quality materials to ensure reliability and optimal performance.Other Products in 'Extron Electronics Products' category
Get in touch with us