8x8 to 72x72 Modular Fiber Optic Matrix Switcher

Product Description

Key FeaturesI/O sizes from 8x8 to 72x72Compatible with all Extron FOXSeries transmitters and receiversSpeedSwitchTechnology provides exceptional switching speed for HDCP-encrypted contentIntegrates easily into a wide range of 4K environmentsMultimode and singlemode I/O boards available3G-SDI I/O board available Optical specifications Number/type 8singlemode or 8 multimode fiber optic inputs and outputs (8 Tx and 8 Rx) per I/O board NOTE Only one fiber is required to transmit video, audio, and unidirectional data. A second fiber is required to transmit return data for bidirectional control/communication. Connectors 16 LC connectors per I/O board Operating distance Singlemode 30 km (18.75 miles) with singlemode (SM) cables with an Extron singlemode transmitter/receiver Multimode 300 m (985) with 62.5 m OM1 multimode (MM) cables with an Extron multimode Tx/Rx unit 1 km (3280) with 50 m OM2 multimode (MM) cables with an Extron multimode Tx/Rx unit 2 km (6561) with 50 m, OM3/OM4, 2000 MHz bandwidth, laser-optimized multimode (MM) cables with an Extron multimode Tx/Rx unit NOTE Operating distance is approximate. These are typical distances. The maximum distance may be greater than these typical numbers depending on factors such as fiber type, fiber bandwidth, connector splicing, losses, modal or chromatic dispersion, environmental factors, and kinks. Nominal peak wavelength 850 nm for multimode (MM), 1310 nm for singlemode (SM) Transmission power Singlemode -5 dBm, typical Multimode -5 dBm, typical Maximum receiver sensitivity Singlemode -18 dBm, typical Multimode -12 dBm, typical Optical loss budget Singlemode 13 dB, maximum Multimode 7 dB, maximum Maximum channel data rate 4.25 Gbps Video fiber optic (FOX I/O 88 SM, FOX I/O 88 MM) Routing 8 x 8 up to 72 x 72 unidirectional (Tx) matrixor 4 x 4 up to 36 x 36 bidirectional (Tx/Rx) matrix Gain Unity Pixel data bit depth 8 bits per channel, 3 channels (R, G, B) Video/audio input or output fiber optic (FOX I/O 88 SM, FOX I/O 88 MM) Number/signal type 8 to 72 fiber optic signals Connectors 8 LC connectors per I/O board NOTE Input comes from an Extron fiber optic transmitter, fiber optic distribution amplifier, or fiber optic matrix switcher. NOTE Output connects to an Extron fiber optic receiver. Digital video SDI/HD-SDI (FOX I/O HD-SDI) Routing 8 x 8 up to 72 x 72 matrix Gain Unity Maximum data rate 2.97 Gbps Auto data rate lock Yes Data types 8 or 10 bit Operation standards SMPTE 292M, SMPTE 259M, SMPTE 297-2006, SMPTE 424M, ITU-RBT.601, ITU-RBT.1120 Digital video input SDI/HD-SDI (FOX I/O HD-SDI) Number/signal type 8 single link SDI, HD-SDI, or 3G-SDI; or dual link HD-SDI per board Connectors 8 female BNC per board Nominal level 0.80 Vp-p 10% Impedance 75 ohms Return loss >14 dB @ 1 MHz to 1.3 GHz Equalization Automatic Input cable equalization distance 3G-SDI Extron RG6, Belden 1694A cable 328 (100 m) Extron R59, Belden 1505A cable 218 (66 m) HD-SDI Extron RG6, Belden 1694A cable 492 (150 m) Extron R59, Belden 1505A cable 328 (100 m) SDI Extron RG6, Belden 1694A cable 984 (300 m) Extron R59, Belden 1505A cable 650 (198 m) NOTE The transmission distance varies depending on the signal resolution and on the type of cable, graphics card, and display used in the system. Digital video output SDI/HD-SDI (FOX I/O HD-SDI) Number/signal type 8 single-link SDI, HD-SDI, or 3G-SDI; or dual-link HD-SDI per board Connectors 8 female BNC per board Nominal level 0.80 Vp-p 10% Impedance 75 ohms Return loss >12 dB @ 1 MHz to 1.3 GHz DC offset 0 V with input at 0 offset Re-clocking Automatic, or use available bypass mode for nonstandard rates Jitter <0.2 UI Rise and fall time (20-80%) 600 ps 100 ps Control/remote switcher Serial control port 1 bidirectional RS-232 or RS-422, female 9-pin D connector (rear panel) 1 bidirectional RS-232, 2.5 mm mini stereo jack (front panel ) Baud rate and protocol 9600 to 115200 baud, 9600 baud (default), 8 data bits, 1 stop bit, no parity Serial control pin configurations Female 9-pin D connector RS-232: 2 = Tx, 3 = Rx, 5 = GND RS-422: 2 = Tx-, 3 = Rx-, 5 = GND, 7 = Rx+, 8 = Tx+ Mini stereo jack RS-232: tip = Tx, ring = Rx, sleeve = GND Ethernet control port 1 female RJ-45 connector Ethernet data rate 10/100Base-T, half/full duplex with autodetect Ethernet protocol ARP, ICMP (ping), IP, TCP, UDP, DHCP, HTTP, SMTP, SNMP, Telnet Default settings Link speed and duplex level = autodetected IP address = 192.168.254.254 Subnet mask = 255.255.0.0 Gateway = 0.0.0.0 DHCP = off Web server Up to 200 simultaneous sessions 7 MB nonvolatile user memory Program control Extron control/configuration program for Windows Extron Simple Instruction Set (SIS) MicrosoftInternet Explorerver. 6 or higher, Telnet General Power supply Internal, 2* (positive-negative), primary and redundant, hot-swappable Input: 100-240 VAC, 50-60 Hz *A redundant power supply is standard. Power consumption Enclosure without boards: 50.7 watts Enclosure fully loaded with 9 MM boards: 165 watts Enclosure fully loaded with 9 SM boards: 171 watts Enclosure fully loaded with 9 SDI/HD-SDI boards: 137 watts Each MM board: 12.6 watts Each SM board: 13.3 watts Each SDI/HD-SDI board: 9.5 watts Ambient temperature/humidity Storage: -40 to +158 F (-40 to +70 C) / 10% to 90%, noncondensing Operating: +32 to +122 F (0 to +50 C) / 10% to 90%, noncondensing Cooling Fan, right to left (as viewed from front panel) Thermal dissipation, full load 584 BTU/hr Mounting Rack mount Yes Enclosure type Metal Enclosure dimensions 14.0" H x 17.0" W x 12" D (8U high, full rack wide) (35.6 cm H x 43.2 cm W x 30.5 cm D) (Depth excludes connectors and buttons. Width excludes integrated rack ears.) Product weight (fully loaded) 61.1 lbs (27.7 kg) Shipping weight 68 lbs (31 kg) Vibration ISTA 1A in carton (International Safe Transit Association) Regulatory compliance Safety CE, c-UL, UL EMI/EMC CE, C-tick, FCC Class A, ICES, VCCI Product warranty 3 years parts and labor