10G Pro AV Over IP Encoder - HDMI Ethernet And USB

Product Description

Key Features New Expanded AES67 capabilities enable any NAV encoder or decoder to transmit or receive an AES67 audio stream New Confidence Preview available in the endpoint or NAVigator browser interface NAV Pro AV over IP Workstation SmartGlide KVM Switching SmartGlide KVM Focus Encodes and streams video, audio, Ethernet, and USB signals over 10Gbps Ethernet networks specification Frame rate2 24, 25, 30, 50, or 60 fps Chroma sampling2 4: 4: 4, 4: 2: 2, or 4: 2: 0 Color bit depth2 8 or 10 bits per color Signal Type DVI v 1.0, HDMI v1.4 and v2.0, HDCP v1.4 and v2.3 Max. video data rate 18 Gbps (6 Gbps per color) NOTE 14096 x 2160 @ 50-60 Hz is available only for HDMI connectors. NOTE 2Subject to the maximum data rate limit. Use our calculator at www.extron.com/8Kdatarate to determine video parameters supported by this data rate. Video input and loop through NOTE *Appropriate DVI-D to HDMI or DisplayPort to HDMI cables or adapters are required for DVI or DisplayPort signal input. Number/signal type 1 digital HDMI video* 1 digital HDMI video (loop through) Connectors 2 female HDMI type A: 1 for input, 1 for loop through Resolution range Up to 4K (4096x2160 at 60 Hz) and UHD (3840x2160 at 60 Hz) Standards DVI v1.0, HDMI v1.4 and v2.0, HDCP v1.4/v2.3 Video processing Digital sampling 8 or 10 bits per color; 600 MHz pixel clock maximum Compression PURE3 Bit rate 250 Mbps to 9.5 Gbps Latency <1 frame (encode/decode) NOTE Indicates minimum latency. Network and video processing dependencies apply. Video output stream Number/signal type 1 PURE3 digital video over IP Connector 1 SFP+ connector (SM or MM) Audio Gain Analog to analog: -6.5 dBU balanced, -12.5 dBu unbalanced HDMI to analog: -5.3 dBu balanced, -11.3 unbalanced Frequency response 20 Hz to 20 kHz, +0.5 dB THD + Noise <0.1% @ 20 Hz to 20 kHz at nominal level S/N Analog to digital: >90 dB, at full scale output, unweighted Digital to analog: >90 dB, at maximum balanced output, unweighted Analog to analog: >90 dB, at maximum balanced output, unweighted Crosstalk <-80 dB @ 1 kHz, fully loaded Stereo channel separation >80 dB @ 1 kHz Sampling Rates 32, 44.1, 48 kHz Bit depths 16, 20, 24 bit Audio input Number/signal type 1 analog stereo, unbalanced or balanced 1 digital stereo, de-embedded from HDMI Connectors (1) 3.5 mm captive screw connector, 5 pole 1 female HDMI type A (shared with video input) Supported formats LPCM (2 channel), analog stereo input Impedance >10 kohms unbalanced, >20 kohms balanced Nominal level +4 dBu, -10 dBV configurable Maximum level +21 dBu balanced, +15 dBu unbalanced Gain adjustment range Adjustable, -18 dB to +10 dB NOTE 0 dBu = 0.775 Vrms, 0 dBV = 1 Vrms, 0 dBV 2 dBu Audio output stream Number/signal type 1 audio over IP LPCM 1 audio over IP AES67* Connector 1 SFP+ connector (SM or MM) NOTE *AES67 specifications are compatible with the Extron DSPs. Network interconnection (NAV) Number/signal type 2 fiber optic Connectors (1) 10G SFP+ connector, 2 LC connectors Termination MDI (SFP+) Ethernet standards 10 Gb Ethernet (802.3ae), 10GBase-LR (SFP+) SM, and 10GBase-SR (SFP+) MM Protocols Streaming SRTP (AES-128) on video, audio, and USB Transport Multicast UDP All supported DHCP, HTTPS, IGMPv2/v3, IPv4, PTPv2, QoS, SSH, TCP, UDP Security AES-256, 802.1X, Active Directory authentication Signal transmission distance Singlemode 10 km (6.25 miles) with singlemode (SM) cables with 10GBASE-LR (SFP+) Multimode 400 m (1312) with 50/125 m OM4 cables with 10GBase-SR (SFP+) NOTE Operating distance is approximate. These are typical maximum distances that may vary depending on factors such as fiber type, fiber bandwidth, connector splicing, losses, modal or chromatic dispersion, environmental factors, and kinks. Nominal peak wavelength 850 nm for multimode, 1310 nm for singlemode Transmission power Singlemode -5.2 dBm, minimum Multimode -3.3 dBm, minimum Maximum receiver sensitivity Singlemode -12.6 dBm, maximum Multimode -13.0 dBm, maximum Optical loss budget Singlemode 7.4 dB, maximum Multimode 8.3 dB, maximum Network extension (EXT) Connector 1 RJ-45 female Termination Auto-MDIX, TIA/EIA T568B Ethernet standards 1 GbE (802.3ab), 10/100/1000 Base-T, half/full duplex with auto-detect Signal transmission distance 330 (100 m) using CAT-5e/6/6a/7 cables USB extension (USB) USB device port Host mode configuration (default mode) Number/signal type 1 USB 2.0 high speed Connector 1 USB type C female Power N/A Maximum built-in USB hubs 1 Minimum built-in USB hubs 0 Optional built-in USB hubs 1 (peripheral emulation enabled) USB device port configuration Device mode configuration Number/signal type 1 USB 2.0 high speed Connector 1 USB type C female Power 5V DC, 500mA (when in device mode) Maximum built-in USB hubs 0 Minimum built-in USB hubs 0 Optional built-in USB hubs 0 Host support xHCI (USB 3.0), EHCI (USB 2.0), OHCI/UHCI (USB 1.1) Data rates Low speed (1.5 Mbps), full speed (12 Mbps), high speed (480 Mbps) Traffic types Bulk, control, interrupt, and isochronous Network switch hops 5 hops (typical) NOTE Network switch hop limitations may apply. Typical limit is up to five network switches. Communications - external devices Serial Quantity/type 1 bidirectional RS-232 Connector (1) 3.5 mm captive screw connector, 5 pole (shared with IR port) Baud rate and protocol 300 to 115200 baud (9600 baud = default) 8 (default) or 7 data bits 1 (default) or 2 stop bits no parity (default), even or odd parity Pin configuration Tx, Rx, and Gnd IR control Quantity/type 1 TTL level (0 to 5 V) infrared (carrier and non-carrier) up to 300 kHz Connector (1) 3.5 mm captive screw connector, 5-pole (shared with RS-232) Pin configuration S = signal and G = Gnd IR output carrier frequency 30 kHz to 300 kHz Contact closure Quantity/type 1 contact closure input Connector (1) 3.5 mm captive screw connector, 2 pole (shared with tally) Input voltage range 0 to 5 VDC, clamped at +5.1 VDC Pin configuration C = contact input (+5 VDC) (Ground is supplied by HDMI connector on an Extron Show-Me cable) Tally port Quantity/type 1 tally output Connector (1) 3.5 mm captive screw connector, 2 pole (shared with contact closure) Pin configuration T = tally output (GND) (+5 VDC is supplied by HDMI connector on an Extron Show-Me cable) USB configuration port Quantity/type 1 front panel USB mini-B Standard Ethernet over USB General Power supply External Input: 100-240 VAC, 50-60 Hz Output: 12 VDC, 2.0 A, 24 watts Power consumption Device 23.6 watts Device and power supply 28.5 watts Ambient temperature/humidity Storage: -40 to +158 F (-40 to +70 C) / 10% to 90%, noncondensing Operating: +32 to +104 F (0 to +40 C) / 10% to 85%, noncondensing Cooling Fan, air flows from top to rear Thermal dissipation Device 71.2 BTU/hr Device and power supply 87.8 BTU/hr Mounting Rack mount Yes, with optional rack shelf Furniture mount Yes, with optional under desk mounting kit Enclosure type Metal Enclosure 1.00" H x 8.75" W x 6.00" D (half rack wide) (25 mm H x 222 mm W x 152 mm D) Product weight 1.5 lbs (0.68 kg) Regulatory compliance CE, c-UL UL,C-tick, FCC Class A, ICES, VCCI, Complies with the appropriate requirements of RoHS, WEEE Product warranty 3 years parts and labor Everlast power supply warranty 7 years parts and labor